Sedmak, Aleksandar.
Sedmak, Aleksandar S.
Sedmak, A.
VIAF ID: 305729207 ( Personal )
Permalink: http://viaf.org/viaf/305729207
Preferred Forms
- 100 1 _ ‡a Sedmak, A.
-
-
-
- 100 1 _ ‡a Sedmak, Aleksandar
-
- 100 1 _ ‡a Sedmak, Aleksandar
-
-
-
4xx's: Alternate Name Forms (3)
5xx's: Related Names (1)
- 551 _ _ ‡a Belgrad
Works
Title | Sources |
---|---|
Analysis of comfort parameters in special purpose vehicles from technological development point of view | |
Application of fracture mechanics parameters to spherical storage tank integrity assessment | |
Cold weld cracking susceptibility of high strength low alloyed (HSLA) steel NIONIKRAL 70 | |
Compatibility of fracture mechanics parameters and fatigue crack growth parameters in welded joint behaviour evaluation | |
Crack growth rate analysis of stress corrosion cracking | |
Damage level estimate of API J55 steel for welded seam casing pipes | |
Determination of bond strength between the hard-faced (HF) layer and the base material (BM) of forging dies | |
ECF 9 - reliability and structural integrity of advanced materials. Vol. 1 / under the auspice of the European Structural Integrity Society and organised by European Center for Peace and Development, University for Peace. - Warley, West Midlands, 1992. | |
Effect of aging on mechanical properties of Al-8Si-8Fe-1.4V/SiCp composites | |
The effect of cracks on stress state in crane wheel hard-surface under contact loading | |
Effect of elevated temperatures on mechanical properties of ultra high strength hot work tool steel H11 | |
Effect of microstructure on tensile properties of austenite-ferrite welded joint | |
Evaluation of the locking compression plates stress-strain fields | |
Experimental and numerical analysis of fatigue crack growth in integral skin-stringer panels | |
Experimental and numerical research of mechanical behaviour of titanium alloy hip implant | |
Experimental in-vitro bone cements disintegration with ultrasonic pulsating water jet for revision arthroplasty | |
Fatigue life estimation of damaged integral wing spar using XFEM | |
Friction stir welding of aluminum alloy 2024 - numerical modeling | |
Impact of choice of stabilized hysteresis loop on the end result of investigation of high-strength low-alloy (HSLA) steel on low cycle fatigue | |
Impact of the life cycle of company to job satisfaction | |
The influence of temperature on mechanical properties of the base material (BM) and welded joint (WJ) made of steel S690QL | |
Measurement of strain using stereometry | |
Mechatronic approach to inventing a novel kind of deformeter | |
Novel risk based assessment of pressure vessels integrity | |
Numerical analysis of constraint effect on ductile tearing in strength mismatched welded CCT specimens using micromechanical approach | |
Numerical and experimental analysis of the fracture behaviour of heterogeneous welded structures | |
Numerical simulation of fatigue crack growth in titanium alloy orthopaedic plates | |
Optical aspect of deformation analysis in the bone-denture complex | |
Optimization of AA5083 friction stir welding parameters using Taguchi method | |
Physical and metallurgic changes during the friction welding of high-speed cutting steel and tempered steel | |
Possibilities of predicting the behaviour of ferrite-austenite welded joints in pressure equipment during exploitation | |
Potential for improvement of comfort parameters in off-road vehicles of Serbian armed forces | |
Practical aspects of fail-safe design : calculation of fatigue life of cracked thin-walled structures | |
[Proceedings] of the 9th Biennial European Conference on Fracture - ECF 9, held in Varna, Bulgaria, 21-25 September 1992. | |
Quality analysis of Al-Cu joint realized by friction welding | |
Reparation of the damaged forging hammer mallet by hard facing and weld cladding | |
Risk management of a hydro power plant : fracture mechanics approach | |
Security and reliability of damaged structures and defective materials, c2009: | |
Selection of the optimal hard facing (HF) technology of damaged forging dies based on cooling time t8/5 | |
Simulation of flat die deep drawing process by variable contact pressure sliding model | |
Stress analysis of steel structure comprising cylindrical shell with billboard tower | |
Stress intensity factors evaluation at tips of multi-site cracks in unstiffened 2024-T3 aluminium panel using XFEM | |
Structural integrity assessment of welded pipeline designed with reduced safety | |
Structural life assessment of oil rig pipes made of API J55 steel by high frequency welding | |
Technical aspects of materials quality : monography | |
Zbornik radova = Conference proceedings |